Tuesday, April 22, 2014

Is Your Tether Quick Release Actually Quick Release?

rev. 7-23-2024

This tether was found by rescue workers at the Wing Nuts accident site; there were several fatalities.

Where do you clip the "spare" leg of a 2-leg tether? To the harness ring, or course, if there is no loop on the tether... and there is not. Pull the quick release and you are still attached by the spare leg. A potentially fatal design error.

This is dangerous even on deck--if the tether gets wrapped around a sheet or guy he has 2 clips to release to get free. Not good.

And this points a scary trend, where equipment companies design to standards but don't actually test the gear in the field. They give the gear to sailors to use, but that is hardly the same as structured testing where all likely use scenarios are systematically tested.

The solution? some brands are adding a ring or loop near the harness end. If you make your own, leaving the loop long enough will do. Or in my case, I simply clipped in a small biner to give myself a parking space.

The typical vendor response? "You should have a knife." Really? Many of us do carry a knife, but that's just one more thing to dig for while you're fighting for your life. You'll probably drop it. Why not just say "I shouldn't fall off the boat?"


Saturday, April 19, 2014

Details

Most dedicated DIYs will recognize these:



These little cones are available for pennies at any Home Depot or paint store and keep your work from sticking to the work bench much more neatly than blocks of wood. Pick up a dozen.


And how do you take the niffy no-background pictures? With a cardboard box, some tape, thin paper or sheeting, and poster paper, a light tent is the trick. I like the daylight compact fluorescent bulbs.


Saturday, April 12, 2014

New Main--Mack Sails

The original sail had slowly turned into a shapeless bag. I priced this one at the Annapolis boat show, and months later, here it is! Certainly, there are some adjustments to be made--batten tension, for certain--but the fit seems good.

I need to fabricate a proper tack strap. The original sail had foot slides, but this one is loose footed. I like it.
Note the jury-rigged boom strap at the clew. I'll have to sew something better... although this worked perfectly.

Draft forward, lots flatter


  • 8.62 oz High Aspect Dacron Mainsail
  • Five full battens with adjustable battslide fittings
  • 3 reefs
  • UHMW wear strips
  • Sail area equal to original design specifications
  • Standard boom cover
 And by way of comparison... Before. We'll be zipping to windward now!



 No swivels of the tackle with twist and friction will increase.


 Why a snap shackle block? I had a spare, no other reason. Notice that I locked the swivel with cable ties.

Wednesday, March 26, 2014

Stitching and Chafe--Not All that Vulnerable

I've been busy testing coverings and coatings, certain that stitiched eye needed consierdaerable protection. But then I started test the eyes themselves. First I sewed a pair of eye in 3/8" Samson XLS, both with the stitch count limited to break at about 2500 pounds. I could sew a stronger eye, but stitich strength is easier to measure accurately when you are not too close to the line breaking strength (stitch/rope interaction become important beyond ~ 60% BS).

 The upper is Robline #10 whipping twine, the lower Robline #10 Dyneema whipping twine. The Dyneema is smaller, but the strength is similar.

Then I abraded each on fresh-sawn yellow pine for 20 minutes on my abrasion machine.  This is just long enough to wear through the line cover, as can be seen.

The polyester stitching is worn (74% of original strength when pulled to failure), but so much as the cover, which is just into the core.

The Dyneema twine suffered no measurable wear (failed at calculated value). However, the cover is gone below the splice, and considerably scuffed where the Dyneema twine did not protect it.

It seems the polyester whipping twine is a more abrasion resistant weave than the cover of the line. Perhaps the wax helps. So while I will still cover my sewn eyes to protect them from UV and wear, I far less concerned than I was. I also need to rethink Dyneema twine; For reasons of stretch,  polyester will remain the choice for nylon webbing and line, but for polyester and Deneema line... I need to do a little more testing. Polyester makes slightly stronger constructions, but perhaps not in the long run. The jury is out. 

Conclusion: polyester twine was basically as durable as the line, and the Dyneema considerably more so. Interesting.

As for UV, the damage is more uniform that we think. This splice is cover only, but the line broke elsewhere.


Sunday, March 16, 2014

Wire Cable vs. Stanchions

I've been investigating chafe protection and Amsteel as it relates to lifeline replacement. Certainly, wire cable is the gold standard. But now I'm not so sure....

After an hour of sawing back-and-forth through a 10mm hole in SS tubing, it had eaten a nice grove and built a corresponding burr on the inside:

After 1 hour.


And though the wire did not look very worn, when we flexed just a bit there was a different story....

Also 1 hour. The damage was not apparent until flexed. Most of the broken wires were inside.

How did Amsteel fare, in the same hole? Before the wire created the burr? Much better with very little wear in an hour. Afterwards, no as well, but still the damage was little more serious than that to the stainless cable. Given that I plan to use 1/4 Amsteel, which is nearly twice as strong as the cable to start with, I'm feeling OK. 1/4-inch it is sufficiently strong that even after 10 years in the Chesapeake sun (not so strong as the desert southwest or tropics) it should have equivalent strength, and with proper chafe guards, the strength loss in the holes should be less than wire. Protected from the son, the pass-troughs may be the strongest part by then.

How does Amsteel like the new hole? Not so bad as you might think and about the same as it like the raw hole, just after I drilled it without deburring. By way of comparison, after the hole was deburred it showed ~ 1/3 this much wear, and if coated with Spinlock RP25, no wear after 2 hours (840 cycles).

After 1 hour on the wire cable gouged hole. About the same as a raw drilled hole, yet much worse than a polished hole.

Alternatively, I tried a dyneema anti-chafe sleeve floating for 3 hours. It could have run for 100 hours without showing wear.

A floating dyneema cover reduces wear to zero.


By way of comparison, this hole wore a polyester line through the cover in 20 seconds and in half in 5 minutes. Amsteel is tough stuff.

No chafe protection? This is the stanchion...

... that caused this.

Saturday, February 1, 2014

It's All About the Feet

Ask a climber what gear is most important--the rope, the pitons, the pack--and they will always answer the shoes. You weight is on your feet and your control of that contact point, not strong arms, gets you up the crag.

With ice it's little different, but shoes are now covered with spikes in the form of crampons, and the fingers replaced by ice axes. While the axes are in your hand, in your face , and most immediate, it is still the feet that provide the base. If the feet sketch about, neither security nor style are possible. And so shoe failures are a major problem. I could just buy new ones, but plopping down $500 for something I will use a few times in a good year and for only so many years into the future is bitter, and I like many things about the ones I have.

 Heel Lift. Traditional rubber strap lacing does a fair job of holding the crampon to the but, but with less than rigid boots and vertical ice,he heels can lift an inch or more.
Enter some non standard lacing, or rather something similar to the new heel cup bindings. By threading the ankle wrap through the heel strap, the hold down force is increased about 30%. A new twist on old tech.

I like the Balatoros for their light weight, easy hiking, and agility on ice, but the same flexible ankles that make them fun, make them tough to front point for long periods. Previously, my Trezeta Sherpas did the job, but they suffered from total separation during a Great Falls ice climbing trip a few weeks ago.

But with bulk removal of rotted foam rubber and massive applications of polyurethane, perhaps they will have new life. But I'm not holding my breath. Perhaps they can finish the season, perhaps a few more. Ugly too, though that probably helps.






Thursday, January 30, 2014

More Ice

White Oak Canyon, this time. Chris and Drew.

The original destination for the day's expedition was Overall Run, but we elected to approach from
Skyline drive and the Park Service elected to close a drive due to icy conditions (1-inch of snowfall). Faced with a barricade, we retreated and drove to White Oak, where predictably good conditions resulted in 3 leads, numerous top ropes, and tired bodies.

Chris honed gear management leading WI 2 on the lower falls. We both bouldered on the cauliflowered base, marveling at the flow, the lace-like structure others travel to view and photograph, but for some reason we are drawn to scale.

Further up the canyon we found the south side to be unstable and thinner than expected. We talked about possibility, then something substantial fell and better judgment prevailed.

The grotto was nice and cold, though and the steep walls nearer the falls provides some short but stiff leads and top roping. And quiet. No company other than the thunk of ax and the crunch of front points.

Nice.



Monday, January 27, 2014

Ice



Although this latest arctic blast has my boat securely frozen in her slip...

Virginia takes on a different aspect, mid-winter.


(50 yards north of the Microdome, Great Falls, Virginia)

Drippy places, unappealing to summer rock climbers, become a playground...


... and thin ice holds a special challenge. (Left of Gorky Park, Great Falls, Virgina)

 




Classic 60s crampons, making the grade; My fancy high tech boots exploded the week before, but old school hangs in there.



Saturday, January 18, 2014

Twine Numbering--They are not Uniform!

As I begin collecting more rigorous data for an up-coming article, I begin testing samples from different manufacturers. I begin searching the net for published data, and I learn a few things that you might already know, and that I knew but just can't get used to:
  • Different company's use different numbering conventions. Robline uses the diameter in millimeters times 10. The others pull numbers out of the air.
  • Strength data is seldom published. The few data points I've found seem accurate, but mostly thread manufactures expect you to guess. Just pitiful.
For polyester twine, some average values:

Robline #4     0.4mm        10 pounds
Robline #6     0.6mm         21 pounds
Robline #8      0.8mm         50 mounds
Robline #10    1.0 mm         90 pounds
Robline #15   1.5 mm        180 pounds

If it is important to you...
  • Make a loop with a fishermans bend or other strong knot.
  • Wrap the line around a broom stick such that the knot is 1 1/4 wraps around from the start. Add another 1 1/4 wraps. In this way, the knot will not break.
  • Hang 2-4 passes over a pull up bar and stand on a bathroom scale. Read how light you are when it snaps, subtract, and divide by the passes.
Then you'll know.

Thursday, January 9, 2014

Taping

Mention tape to a sailor and they think of rigging tape, sail repair tape, and tell tail tape. If they're working on a project, perhaps luff tape or fiberglass tape. Maybe even duct tape.  But those aren't what we use the most of.

Athletic tape. Not very durable, in fact, down right temporary. It's purpose is one-day application for the treatment of prevention of sprains and strains.

I suppose I got the habit back in my climbing days, when taping for abrasion protection was standard for the rough crack climbing we were exploring at the time. Taped up like a boxer (not as thick), we would plunge our hands into 1- to 2-inch cracks lined with razor sharp crystals, twist and cam, and pull ourselves up to crazy heights. I could go through 2 roles in a day if the climbing was tough. Today we went ice climbing; the sole of my boot decided to peal wide as a whale, leaving me flapping and clownish. Tape to the rescue.

Uses on a boat?
  • Tiller grip. Doesn't last too long, but renews in seconds.
  • Securing rope ends while coach whipping.
  • Protecting stitched eyes from UV. Conforms nicely and holds-up if painted.
  • Rigging tape. Doesn't last, but is also porous and does not deprive stainless of oxygen.
  • Pre-wrap in stainless tubing, so that clamps hold better.
  • Protecting stainless from scratching under clamps
  • Non-scratch bottom on anything you don't want scratching the varnish or gelcoat.
  • Tape your knuckles before sanding; can save a lot of lost skin (as strip over the areas to be protected, then a thing ring between the fingers to keep it in place).

Like duct tape, but cloth, there are many uses. Keep a could of rolls handy.

And the "athletic" uses are endless, treating the bumps and bruises that come with cruising. Almost as vital as ibuprofen.
... and many more.