Sunday, April 11, 2010

Yo-Yo Fishing

rev. 3/18/2011

If you hail from south Florida or the Caribbean, you should already know this one; the Cuban yo-yo. In it's basic form, it is fishing reduced to its origins; hand lining. Popular in Cuba, is has been brought to south Florida and is quite enjoyable for its shear simplicity. Toss a few yo-yos in a bucket and you can catch some fish. Perfect for a crowded cruising boat or a small day-sailer. Rigged as a simple trolling set-up, catching game fish under sail couldn't be simpler.

The Yo-Yo. There are 2 sizes: the 6-inch inside diameter size is best for hand lining and comes loaded with 300 feet of 40-pound test line, a 1-ounce sinker, and a hook; the 8-inch inside diameter size is typically sold empty and is well suited to the trolling set-up I will describe below. Both are simple spools designed with simple features that make a big difference:
  • Wide, deep, and smooth, for easy line pay-out and secure storage.
  • Lower forward lip for better line pay-out.
  • Finger grip inside spool for secure grip while casting or winding in a big fish.
 Any Florida bait-and-tackle store will have these for a 3 to 5 dollars.


Handlining. Just bait up and lower over the side. To cast, let out about 3 feet of line, pinch the line against the side with your thumb, and whirl the bait and sinker over your head like a slingshot. Understandably, casting is a bad idea on the deck of a  sailboat, but solo in a tender or on the beach it works well. To reel in, simply wind the line back on the spool. If you hope to fight a large fish--and these can mange some big fish--sailing gloves are a good idea, though I almost always forget. You don't actually fight the fish with your hands--you use the reel. We keep two in our tender all summer. We loved "The Old Man and the Sea" and this takes us there. Yo-yo demonstration

 A source for yo yos: Bass Pro Shops
(Only 6-inch yo-yos. They do not stock yo-yos in the stores.)

Another source: Palm Bay Bait and Tackle

And yet another source: http://www.stingraytackle.com/9incubanreelyoyo.aspx
(I just bought a few 9-inch yo-yos from these folks (March 2011) since I'm not traveling to Florida soon.)

A source for wooden yo-yos, if you must be completely traditional: http://www.fishingyoyo.com/about-us.html

A source for flat line clips: Bass Pro Shops
(Flat line clips can also be made from tarp clips for a fraction of the price; available from Home Depot or most hardware stores, simply line the teeth with a layer of athletic tape. tarp clips)

  
Trolling. Though not the original purpose of the yo-yo, this is where they shine. Although I do carry trolling rods, the yo-yos catch most of our fish, because they are fast to rig and consequently, we use them more often. They are compact, quick to rig because the line, leader, and lure can be stored assembled, and tangle-free.

  • Load the yo-yo with 150 to 200 feet of 60- to 100-pound test line. Attach the line to the yo-yo with a slip knot with a fishermans knot or improved clinch knot.
  • Add a trolling sinker, 2-6 ounces, to suit typical depths and speed. Some fish (mahi-mahi and other bluewater fish) prefer surface lures that incorporate all the weight that is needed.
  • Add a 20 foot leader, to separate the lure from the sinker.
  • Pick a lure. I like 6- to 8-inch Rapella diving minnows for bluefish and striped bass. I also use bunker spoons and hose eels. However, the best bet is to match what the local charter boats rig. Rubber fish, feather lures, and squid-types are popular for bluewater game fish.
  • Let out all of the line at a suitable speed; 3-4 knots for striped bass, 4-6 knots for blues, mackerel, and bluewater game fish, though these are just guidelines.
  • Attach the yo-yo to the stern rail with a sling and carabiner. Some suggest a bungee cord attachment, to help absorb the strike of a big fish. They haven't done the math; the stretch inherent in the 200 feet of line you have out is more than enough--it will easily stretch 10-20 feet with a big fish--and any difference is in the head. I've had a 36-inch rockfish strike while I had the yo-yo in my hand, adjusting something, and the strike was nothing more than a steady pull. I've only lost a few lures, but I believe they were crab pot snags, not big fish. I've caught rockfish up to 39 inches with little strain on the gear.
  • Clip the line about 2 feet out to a flat line clip (a loop of line will give a cleaner release), removing the tension from the yo-yo and allowing it to hang down; in this way, you can see a hit. The pictures should make this clear: the top shows a yo-yo with a fish on, while the bottom is set with the line clipped to the trolling release (flat line clip).
The yo-yos are mounted center, port, and starboard, and 2 more on 7-foot outriggers (bamboo poles hidden behind the mainsheet). We tried a variety of lures. For us, large Rapella diving plugs work for rockfish, and yellow hose eels for blues. But I try other thing occasionally, since someone always swears by something different.

Our typical trolling set-up includes 3 yo-yos--one each corner and a trolling rod in the center, though the center line seldom hits. Sometimes we set 5--2 more on outriggers. But when not purposefully fishing, we may just set a single yo-yo on a corner railing. Our catamaran has a 16-foot beam and this gives adequate line separation; with a narrower transom, only two lines should be set. They it  store in a cockpit locker and can be set in a minute.



Where to fish? That is the trick, and local knowledge is best. But for a start, channel edges and off the beach in about 25-40 feet of water are good places to start.





It works!


------------

And from the United Nations, this summary of village fishing methods for the third world.

 

Banning Bugs - Slider Screen for a PDQ 32

rev. 11-26-2010

Every boat is a compromise. For 32-foot catamarans, one such compromise is providing standing headroom on the bridge cabin without too much windage or too little wave clearance under the bridge deck. The Gemini 105mc compromises by providing a wave-scraping 3 inches of clearance and terrible visibility forward.  The PDQ 32 does it with a slider that can be closed for inclement weather. It is well covered by the hard top, but mosquitoes fly right in, unless the slider is closed, causing ventilation to suffer just when it is needed most.

We added a removable screen, attached by Velcro, that rises from the bulkhead to the ceiling. We attched medium-duty self adhesive Velcro at about 12-inch intervals to both the boat and the net. There's a trick--although Velcro sticks well to gel coat, the netting provides a challenge, since there is no surface area. However, if a matching square of duct tape is pressed on the opposite side, the adhesive coatings see each other through the mesh and the grip is positively tenacious. I may tailor a more permanent version later, but so far the beta version seems very workable.

Dark netting gives far better see-through visibility than white netting. The dark netting does not unduly hamper forward visibility.

Ventilation is maintained and the screen can be left in place if motoring a bug infested river on the Inter-coastal Waterway or the Chesapeake. The door is unobstructed.

Note: after 2 seasons in some bug infested areas, the only required upgrade was to add some more Velcro. A continuous strip of the hook side on the ceiling prevents the dirty buggers that congegate there from cralwing under the edge. We did not add additional velcro to the netting, since the hook part catches just enough in the netting to close the gaps,without making installation and removal a hastle.

We were able to leave it up when motoring in some particularity bad areas.

Sunday, April 4, 2010

Ethanol and Gasoline and Diesel - References

rev. 10-14-2010

There is little question; although the addition of ethanol to gasoline has caused no impact to the motoring public - other than a bite in the wallet at tax time and at the grocery store -  the boating community will be living with the down sides for years to come. A few articles containing pertinent facts, since there is certainly plenty of rumor in circulation. These seem to support my varied experiences with several boats. I have kept my opinions to myself.

Will ethanol find its way into the diesel supply? This has been discussed but is not yet in practice. There are links below regarding this potential as well.

I will add more articles as I find them.

______________________________________________________

Gasoline/Ethanol. E-10, possibly moving to E-15 and beyond.

E-15 Aproved by US EPA. Only for 2007 and newer cars, but broader approval is expected.
http://www.thedetroitbureau.com/2010/10/epa-gives-limited-waiver-for-use-of-e15-gasoline/

An interesting report to Australia Environment. Some good technical information about E-10 to E-30 concentrations that I have not seen elsewhere. A different spin that most US documents. Enleanment is addressed on page 10, vapor pressure on page 15, and mileage on page 26. Read the whole piece.
http://www.stealth316.com/misc/review-impacts-of-ethanol-gasoline-blends.pdf

EPA is likely to approve increase from E-10 to E-15 by mid- 2011. They are waiting on tests expected to be completed in June 2010. These are automotive tests and do not address marine or motorcycle engines.
http://www.reuters.com/article/idAFN0149521120091201

The volume of biofuels will probably triple in the next 12 years. This will include ethanol and bio-diesel. The amount may be less if the fuel is not available, but the EPA clearly has authority to increase the geography and concentration of ethanol in gasoline.
http://www.ethanolrfa.org/resource/standard/


EPA memo on E-10 and phase separation. It explains why temperature changes can cause dramatic fall-out. It explains that EPA based their absorption risk statement on a relative humidity of 70% and 70F temperature. Since many boats see humidity very close to 100% and are not used for 6 months at a time, as general reasoning it is reasoning is flawed.
http://www.epa.gov/otaq/regs/fuels/rfg/waterphs.pdf


White paper on ethanol fuels from Renewable Fuel Association. Includes simple home-test for ethanol content of gasoline (page 31) and information on vapor pressure (page 12-14). Higher vapor pressure equals increased tank breathing, a factor the EPA phase separation analysis disregarded.
http://www.ethanolrfa.org/objects/pdf/newRFA%20Fuel%20Ethanol%20960501.pdf


Also from the RFA site (buried in the Technician's paper):
Enleanment: Oxygenates such as ethanol chemically enlean
the air/fuel (A/F) mixture. As an example, in engines set at an
A/F ratio of 14.7:1 on all hydrocarbon fuel, the introduction of
3.5% oxygen in the fuel would enlean the A/F ratio to about
15.2:1. Computerized vehicles can compensate for this shift
by sending a command to increase fuel flow. Most nonautomotive
equipment is not sophisticated enough to accomplish
this. However, this small change in air/fuel ratio is not of
concern in most equipment and usually no modifications are
required. Some manufacturers have expressed concern that
the enleanment resulting from fuel bound oxygen could create
problems in certain severe applications. In particular, there is
concern about continuous operation at wide open throttle
(WOT) such as in marine applications. Also of concern is
equipment that typically operates rich at specified settings.
An example here would be snowmobiles. The two primary
concerns are octane quality and excessive heat. Properly
blended ethanol blends should not present problems in the
area of octane quality because ethanol is actually an octane
enhancer. Ethanol is routinely used to improve the octane
quality of gasoline. The more predominant concern is the
potential for higher operating temperatures. The maximum
combustion temperature (and resulting engine temperature)
occurs at an air/fuel ratio of 14.7:1. Going rich or lean from this
point will result in lower temperatures. Therefore, equipment
with richer initial A/F ratio settings such as 13 or 14 to 1 may
experience increased operating temperatures when switched
to oxygenated fuels. This increase is not significant and most
manufacturers do not require any modifications, but some do.
For instance, Polaris recommends that their older carbureted
sleds "jet up" one size when operating on oxygenates. Further,
some of their fuel injected 2 cylinder models require a
"shim kit" to lower the compression ratio. Polaris fuel injected
3 cylinder models are computerized and the E-Prom is already
calibrated to compensate for changes in oxygen content.
Arctic Cat recommends that when using oxygenated
fuels in their older Tiger Shark Watercraft, the high speed
needle valve should be "opened" 1/8 of a turn from its setting.
In the case of their Arctic Cat sleds, they recommend "jetting
up" the carburetor jets one size. Only a handful of marine and
recreational manufacturers offer such recommendations but
consumers should be advised to consult their owner's manual
or servicing dealer to determine if any modifications are
recommended.
Excerpted from (pages 33-36 discuss non-automotive engines):
http://www.ethanolrfa.org/resource/technicians/documents/ChangesinGasolineManualIV-UpdatedLogo.pdf
  

 White paper from the National Marine Manufacturers Association regarding ethanol and aluminum tanks corrosion.
white paper


 Practical Sailor Testing. None of the tested additives were able to prevent phase separation in E-10 gasoline, including several well know brands that claimed they could. Typical puffery in an unregulated market.
http://www.practical-sailor.com/issues/34_11/features/Ethanol-Gas-Additives_5692-1.html


Corrosion problems with E-85. Every state publishes similar information; this is from Florida. No, boats don't run E-85, but when the fuel separates, the water phase concentrations are this high and these are the problems we see.
http://www.dep.state.fl.us/waste/quick_topics/publications/pss/tanks/ethanol/EthanolStorageinUSTandAST.pdf

________________________________________________

Diesel/Ethanol. Only discussion at this point, since retail sales is not permitted at this time. Presumably, since boats are off-road, it would still be permissible to use #2 fuel oil, which could not be converted to ethanol blending because of the overwhelming danger of fires in home and apartment furnaces.


USEPA is researching the possibility of adding ethanol to diesel. Nothing has been decided at this time, although clearly the ethanol lobby is pressing hard.
http://cfpub.epa.gov/ncer_abstracts/index.cfm/fuseaction/display.abstractDetail/abstract/7946/report/0

 DOE is researching ethanol/diesel blends. However, this is only a combustion test in an engine, not research on the broader topic.
http://www.nrel.gov/vehiclesandfuels/npbf/pdfs/35334.pdf

 This DOE study addresses safety and some practical problems. It discusses problems such as phase separation (ethanol does not stay in diesel as well as it stays in gasoline), flammability, and high cloud point (room temperature). They discuss all of this from a truck view point, not marine.
http://www.nrel.gov/docs/fy03osti/34817.pdf


Friday, March 26, 2010

Seven Sins I Will NOT Commit This Spring

I believe in sailing, not sitting on land. I believe in material maintenance and functional improvements and not in primping. Yup, another rant.


1.  Wax-on/Wax off
From what I've seen gel coat can do 40-50 years without real attention, and then there's Imron if I'm still on this side of the dirt... which I doubt. I'd rather paint the boat once than wax it 45 times. Caveat: windows are easier to see through and last much longer with regular wax and covers. They are also harder and more expensive to replace, per square foot, than paint. I pamper the windows a bit.

2.  Scraping Bottom Paint
I use ablative or self polishing paints, and if sailed enough and scrubbed just a few times, there is zero build-up. My last boat was never stripped in 29 years, and frankly, she didn't need it. We hit 15 knots in 12 knots of wind on her last sail with me at the helm, a sea trial for a prospective buyer. Some people worry that soft paints release more copper into the water, but if used until spent, there is little difference; all of the copper in either type is in the water. Caveat: if you race, you'll want a hard paint that you can scrub every few weeks - but not me. That first spring scrub is going to be in cold water, or if you wait until it's warm and things can grow, it's going to be a bear.

3. Draining Fuel and Carburetors / Refilling in the Spring
The trouble is, unless you truly get the carburetor dry, it will always dry out and leave gum. On the other hand, if you leave the carburetor full and start the engines each month, even in the winter--what I've been doing for 25 years--the carburetor won't dry out. A carburetor vent filter slows the process even more, reducing water absorption and oxygen as well, combined with a fuel tank vent filter. After a few seasons of winterizing the boat and having troubles in the spring, I've learned sail all year--even if on a limited basis-- is simpler. Filter/separators help, even with gasoline. If I hauled out for 3-4 months my practice would not change--fuel doesn't evaporate or deteriorate that fast when it's cold, and when it gets warm, I'm back in the water. I love it when calculated sloth is best.

4. Projects Requiring Epoxy...
... or any other temperature sensitive adhesive, sealant, or paint. I hate big spring projects. They delay the sailing season well into summer, waiting for enough good days, on week-ends and in a row, to get anything accomplished. There is a temptation to start earlier, to do it anyway, since 50F seems warm after winter, but the results typically suffer. Even if the days are fine, the nights are too cool for optimum curing. Some products - 3M 4200 and butyl rubber tape - have lower temperature limits. Paints are generally very fussy. Check the labels. Epoxies will eventually cure, but unless specifically formulated for low temperatures they will never reach full strength. Some adhesives will never cure properly. Instead, haul-out briefly in mid-summer, when the weather is dependable. Pre-fab what you can and knock it out swiftly. Chill the epoxy before use, so it doesn't go off too fast in the heat. Paint in mid-morning.

5. Varnishing Exterior Wood
I love to watch other people bending over the rail, sanding away. I admire the results and I love classic boats.

6. Scrubbing
Surely, you jest. I clean the windows, vacuum as needed, and maintain zero clutter on deck and in common areas. Cushions covers get laundered when needed. That's it. I hose off the bird poop when it becomes unbearable, but I can bear much.

 7. Recommissioning
I sail all year. Spring commissioning, for me, is filling the water tank when the dock water comes on (flushing take only seconds), swapping the storm windows for screens (10 seconds each), taking the electric space heater home, and by summer, taking some blankets home. Caveat: if I lived in the far north, where harbors freeze for months, I would act differently.


And then there is the more traditional list:

1. luxuria (extravagance)
2. gula (gluttony)
3. avaritia (avarice/greed)
4. acedia (acedia/discouragement)
5. ira (wrath)
6. invidia (envy)
7. superbia (pride)
Unfortunately, I enjoy these.... The boat is an extravagance, I like beer, I covet large and small catamarans, I discourage myself continuously, I enjoy swearing at old engines, I wish I could take a season off like others, and think my PDQ's pretty cool. I'll focus my effort on my personal list--I have a better chance of success.

I love to tinker--the evidence is all over this blog--but it will not cut into my sailing time. The focus will be function, but I will slip in some primping here and there. Please don't tell.

So many Chesapeake sailors park their boats in September and don't get them wet until May or June; over 60% of the sailing season is spent on blocks or at least with no intention of moving. I don't get it.