Wednesday, December 25, 2013

Got Rope?

I've had this 30-year old anchor rode hanging in a tree for 15 years, serving a second life as a Tarzan swing. I've got a Kevlar genoa sheet with a shattered core, no longer trust worthy for anything critical.

The rope ladder was a simple project. I've wanted something that was compact, couldn't harm gelcoat, and could be used climbing in or out of the tender. This took about 20 minutes and about 30 feet of line (2x the length + 3' for each rung). A fun night-before Christmas project, complete across my lap, with a glass of hot tea at my elbow, while watching The Polar Express with the family.

The door mat required 100 feet of 1/2 inch line and about 2 1/2 hours to complete. The knot in the middle is rather a lump underfoot, but it looks very traditional. The wrap and sewing took the real time. I soaked it with the borax/washing soda/baking soda anti-mildew blend when finished. My mom thought it a charming gift; since we had enjoyed it on the boat and in the backyard for many years in previous incarnations, it has history with her children and grandchildren.

And 2 lumps of old rope were thus consumed. Good.


Via Ferrata Tethers--Some Good Ideas, But Not for Sailing


Via ferrata trails, literally iron ways in Italian, are climbing trails equipped with rungs and safety wires that allow fit but unskilled personnel to move quickly and safely over difficult terrain. Though they date back into the 19th century, they are best know from their use during World War I, moving troops through the mountains.  Since then they have expanded to thousands of tourist routes in Europe and the United States. Since tether technology is the focus of this post, I'll leave history research to the reader; the internet is great for that.

The climber is protected falling all the way by a pair of tethers that follow a safety wire to the side of the rungs. Periodically, the wire is fixed to the face, and this is the challenge; these points are generally  10-20 feet apart, allowing for  serious falls before the tether takes, and requiring the tether to absorb a great amount of energy, more than a dynamic rope alone can handle. Dynamic ropes are rated for a fall factor of 1.8, whereas a via ferrata fall can be fall factor 5 or more.


The solution is a more extensive energy absorption system, including either friction through an aluminum plate or a tear-type energy absorber, like a Screamer.


Why wouldn't these make useful sailing tethers?
  • The allowable impact force is much greater, since the load is taken on a seat harness rather than a chest harness; the human tail can take a lot more force than the ribs. Sailors need a softer catch.
  • The falls are really much greater. A sailor will never see an impact beyond fall factor 1; the ISO drop testing required by the ISAF rules is based on a FF1 with a 100Kg mass.
  • The end clips on via ferrata tethers are applicable and gaining popularity. The West Marine tethers are now Kong Tango via ferrata biners (pictured on tethers to right), and I like them very much. Fast on and off, one-handed even when cold and wet, locking, light, and fit over most handrails too. Because they are aluminum, they do require periodic lube and rinse. Mine have held up very well, like new after 2 seasons.
  • Harness attachment. Sailors like a quick release on the tether, something that can be removed under load. Climbers opt for a locking biner, since no possibility of accidental release is acceptable. Most often the tether is cow-hitched to the harness.
  • Length. Sailors like dual lengths (2-3 feet and 4-8 feet) while climbers are restricted to 2 matching arm's length tethers; they never want the clip to move out of reach (if it snags below you this is a real drag).
Certainly there are some ideas here, some worth adapting, but the application is different.

-------

Note on recalls. Because of the extreme nature of the falls and untrained nature of many users, there is some history of failures, most often fatal. In general, the causes have been:
  • Fall too great. Anything of 10 feet is trouble and over 15 feet is beyond the equipment rating. The via  ferrata trails generally recognize this, placing tie points ever 10-15 feet, but risk is often part of  climbing; if it looks too scary, go down.
  • Worn friction rope. Some designs rely on a rope slipping through a plate with many holes. If the rope wears through use--tour groups use them daily--the rope slides more easily and insufficient energy is absorbed. This type has gone out of production because they are too difficult to inspect.
  • Poor or worn stitching, or any other construction fault, though this type of failure can result from too long a fall.
ALL via ferrata falls are bad, far more dangerous than falls on a climbing rope. They feel safer but are not. The impact forces are high and there is much to hit on the way down.

Monday, December 23, 2013

Fids

When we need something, we run to the corner store store, or worse, the mall. When we some thing for the boat, we run to the chandlery, West Marine most probably. What we need is on the shelf. Seldom do we give a thought to making simple tools, though isn't that capability what made us human? Back in the day, for a workman to make his own personal tools was central to the craft. What sailmaker bought his fids from a store? Seam rubbers and wooden fids were crafted as needed, to the individual taste and hand of the worker. Some made fids with a handle or a turk's head worked in a turned grove; this probably worked best for large course hemp lines, but on a small boat with synthetic line, needs have changed. Even my wooden fids are smooth, so that they can pass through one line, towing another. The point is they were made by me to work best for me.

My finishing bench is of my own creation, fits nicely next to my favorite chair, always holding what I need near at hand (I have another sewing kit on the boat). It is a bit smaller than old-time benches, better suiting the size of my projects.

My wooden fids were turned from scrap hardwood dowel in a drill press (I have a lathe, but the drill press is handier for this) and have been worn smooth. There is a hole in the butt to accept a towed line, when that is required.They took perhaps 15 minutes to make, and I enjoyed the process.

My hollow fids are discarded knitting needles. Ask your wife or daughter--I'm they have a few mismatched needles about--or go to a thrift store. Cut to length, smooth the outside edge with a file or sandpaper, and clean the inside edge with a hand held drill bit. I seriously doubt the commercial hollow fids were purpose built, as the volumes are far too low--they are re-puposed knitting needle blanks, I'm sure of it.

Wednesday, December 18, 2013

Tangier Island Seeking More Cats--Who Would have Thought



When we first visited Tangier, we were greeted at the Park's Marina by about 50 cats, all fed by the owner. At some point, someone had a problem with this state of affairs, and the town’s leaders brought in a SWAT team of veterinarians to spay and neuter their increasingly out-of-control cat militia. Unfortunately, they hadn't done all of the math.

RiverottersMDNR
Now the otters have the upper hand, stealing soft crabs so conveniently placed in shedding tanks, available nightly under convinient work lighting.

Some of the waterman have gone back to keeping cats on their shedding platforms. Though a cat is no match for an otter, a group of cats is sufficient deterrent.

I suspect we'll see more cats during our next visit.

Read the full text here.

 

Sunday, December 15, 2013

Heater Efficiency

Marine space heaters are not typically rated for efficiency by any approved method, and Internet folks are forever commenting on what is efficient or not efficient, without any engineering basis or understanding of the math. But it isn't complicated and engineers have long known you can calculate everything you know from the stack conditions. After all, what goes up the stack didn't go into the room.

I described my heater installation and early experiences, but I only estimated the efficiency without rigorous measurement. Time to fix that.

Stack Temperature. Obviously, cooler is better. Since the stack temperature on my Dickson P9000 is 185F on a cold day (40F), that gives me a starting point efficiency of 88.5%. However, since the Dickson unit preheats the combustion air with flue gas, this gives a 4% increase to 92.5%. So little, you say? In effect, I'm simply moving the exhaust temperature 200F. It is worth doing simply to keep the hull fitting cooler and to reduce burn potential on-deck. More importantly, while dropping the temperature of the exhaust 200F is not a big deal in terms of efficiency, it means the P9000 exhaust can't damage a nylon rope. That is a big deal.


Excess Oxygen. However, the easiest way to get a cool stack is plenty of excess oxygen. A few percent is desirable, but the rest is energy wasted heating air. I get a reading of 5% on the Dickson heater, and that costs me 2% on heater efficiency; down to 90.5%.


Ambient Temperature. It is also necessary to do a correction for ambient temperature, compared to the base temperature used int he first graph (70F). Colder inlet give the impression of higher efficiency. By observing performance at 40F vs. 70F I gave myself some false credit. Subtract 1%. Down to 89.5%.


Overall Efficiency. Just start at the top and add them up. 88.5% + 4%(preheat) - 2% (excess O2) - 1% (testing temp correction) = 89.5% thermal efficiency.

AFUE (Annual Fuel Utilization Efficiency) Rating. This rating, found on every home furnace, is a bit different, as it includes losses up the stack when the unit is not firing; for example, fire places can be great heat wasters since warm air goes up the stack even when not in use. However, all of this is irrelevant to a simple marine heater such as the Dickon P9000 (it runs steadily without cycling--it can be turned down), I have not considered it. However, for the purposes of comparison, the AFUE is generally about 15% lower than the thermal efficiency. However, since the Dickson is sealed (all combustion air comes from outside) only a minimal 5% penalty is applied. Electric heat is assigned no penalty, so I am being conservative. 84.5% estimated AFUE.

Bottom Line. So how does this "stack-up?"  This little marine furnace rates as mid-efficiency. Not too bad for something the size of a toaster and much better than more primitive predecessors.


Saturday, November 23, 2013

Singlehanded Kayak Loading--Onto the Car with a Bad Back...

... or if you short, or even exhausted after miles of paddling.

This is so obvious it should be in the owners manual. They should use it as a sales pitch. But it didn't occur to me until after returning from a trip with our stuff piled in the driveway, that most kayak wheels look kind of like a bike rack with wheels instead of arms. They have the same padding and the same angle, and at least one strap for securing wheels to the boat.



  1. Secure the existing strap to the roof rack with the padded arms straddling the break in the roof line.
  2. Secure a second line to the bottom of the hatch to hold it down. I had to add this one, a few minutes work.
  3. Roll it up and then flip it over to better secure.



Yes, this can be done simply with a blanket or large towel, but by the time you secure the towel that takes time. Fail to secure the towel and you'll lose paint for certain. The heavier the boat and the higher the roof, the better the wheels work.

 While I don't have any trouble simply lifting kayaks onto my Forrester (pictured), the wheels are a BIG help when loading onto a high SUV or van, which is nearly impossible for a 5'8" guy; I simply run out of height by the time I reach over the rack.

Saturday, November 16, 2013

Marking Furler Line

I had always marked one spot on the furler line; the 100% setting, which I used when reefed. However, adding the inside genoa track prompted me to refine the system.

  • Wide band: 110%, just short of touching the shrouds and spreaders. While it is possible to run a full genoa between the shroud and the spreaders, it risks sail damage and is more trouble than it is worth.
  • Medium band: 90% Just short of lapping. A nice setting if single or double reefed, going to weather.
  • Narrow band: 70%. Small, only 25 % of full area. Good for double reefed and blowing like stink.
To insure the whippings are tight and can pass the jammer smoothly, they should be smaller than the line. This is easily accomplish by holding the line stretched between 2 winches while whipping.

 
Yes, you can always adjust as you go, but rolling sail in a breeze isn't good for you or the sail. Advancing the furler line to the correct setting before unfurling is MUCH easier.

Fog


Sunday, November 10, 2013

Amsteel... or Not?

Some folks are so stuck on Amsteel that they probably use it for shoe laces (I've seen soft shackle key rings). Others treated as some new fangled nuisance, like polyester sail cloth, that will soon go away. I've been using soft shackles on my genoa sheets for a little while now and I like them. Are there other applications I should consider?

In use

Genoa Sheet attachments. Why? I recently add an inner track which requires changing sheets occasionally (there are 2 sets now). I didn't trust snap shackles on a flogging sail, couldn't justify the expense of  J-locks, didn't fancy getting whacked on the head or having the mast pummeled. I could have used stropes tied from polyester line (I did use these for a time), but the strength is close and there is a slightly greater chance of opening (they never did). The hollow braid and slipperiness of Amsteel permits some unique splicing options.

Genoa sheets. I recently installed some line that was donated to me (testing left overs). Turns out it was 1/2-inch Warpspeed (21,000 pounds BS, $5.67/foot). Stiff as hell but good in this application, should last a very long time. Nice hard on the wind, where stretch means the sail gets full when a gust hits, which is when you want it flat. But I would not have spent $300 for it! I didn't realize it wasn't Staset until I saw how it handled and looked more closely at the core.

When something wears out

Lifelines. Certainly, in a few more years. I will go 1/4-inch with 9/16-inch webbing on the wear spots, which even with UV should be good for 10 years. Easy to do, nice hand, and light.

Jib halyard. My jib halyard has one tight spot where it passes through the masthead. I think the smaller size will resolve the pinch. I will have to splice to something larger for the jammer.

Spin head attachment. If it breaks. Not likely. Or if I need it elsewhere (more likely).

Spin tack. The metal shackle snags and scrapes on the forward lifeline. This will be converted to a soft shackle soon, certainly before the lifelines are changed.

Bridle to chain. If I lose the Mantus hook I'm testing, Amsteel as either a loop or a soft shackle will be next. Easier than the plate I was using. Honestly, for me a sling and carabiner work very well.

Main Halyard. Lower stretch would be nice, but that will be some years.

Topping lift. Light, don't often adjust.

Bad applications (to me)

Spin sheet attachments. Snap shackles are faster.

Main halyard. I prefer a knot. Easy to trim a few feet every few years, to move wear spots.

Jib halyard. Only pin shackles fit furler.

General block attachment. I would be open to this, but in any cases there are sharp edges. Pin shackles generally last forever.

Lashings. Generally nylon or polyester are strong enough when passed many times. Amsteel knots poorly, giving no increase in security over a good lashing.

Main sheet. I want some stretch during jibes; a high mod line increases the stress on the traveler bearings. I wish my traveler was not Spectra and I will change it if I find something cheap.

Jib sheets. Good application, but not cost effective for this boat. I have polyester for my reaching sheets, which is fine, and Warpspeed for the windward sheets which is perfect for that.

Spin sheets. Again, I like some give.

Tying things on deck. Poor knotting, simply don't need the strength.

Anchor bridle. You need the stretch of nylon with chain. But if you are using all-nylon rode, Dyneema may be just the thing to limit yawing; I've tested it, it works.

Jacklines. It depends. On smaller boats the stretch of polyester reduces forces. On larger boats, Dyneema is perfect.

-----------

And so it seems to be limited in application. Neat stuff, though.




Wednesday, November 6, 2013

Sucking Bottom

I never thought of my PDQ as a freighter, but they have a few things in common. I keep expecting--hoping--her to behave like a beach cat, but she's not.

Something we all keep any eye on, at least occationally, is maximum speed under power. It 's an indicator of whether the engine is tuned well and the bottom is clean. If she reaches top speed, we know those things are fine.

Yesterday as I was motoring back in I pushed the throttle wide open and she went... 6.5 knots. I've been seeing 7.4-7.5 knots since I extended the transoms, so something had to be amiss. I looked over the stern at the transoms; they were 6 inches under water unde conditions that should have them just above! Am I taking on water?

And then it occurred to me that I was sprinting across 4.5 feet of water and the hull was feeling the bottom, both in terms of excessive stern wave and reduced pressure under the deepest part of the hull. In fact, I was much closer to the bottom than my nominal 3.5 feet of draft would suggest. I suppose I might have touched, though I didn't feel it. Perhaps sprinting across shallows is not so smart.



As soon as I moved into the channel--8 feet--the speed jumped to 7.5 knots and the transoms came up. I think that's fooled me a few times over the years, wondering what I'm dragging.

------------


Pilots bring freighters into port often reduce speed in shallow areas to avoid what is called squat. It is more than simple caution and is calculated before entry.